Reviewing this and it seems wrong.
This looks more correct to me.

route-map link-a-in permit 10
set weight 200
route-map link-a-out permit 10
route-map link-b-in permit 10
set weight 100
route-map link-b-out permit 10
set as-path prepend 64512

Passed this morning. Thought i'd bombed it but low and behold...... PASS
3 sims up front. Got no drag and drops this time. Several of the multiple choice questions were new. Maybe 4 of the 40 questions were ones not seen here.
The sims:

all my sims were very similar to the ones found here but there were drastic changes on some. 


VRF & EIGRP Sim:
The IP between R2 and R3 Admin was a 192.168.x.x while all the rest were some form of a 10.x.x.x/30 
for this I:
router eig <AS>
network 10.0.0.0
and or
network 192.168.0.0 
^^^ that popped all the wings into the EIGRP routing 

Next step was to fix some bad autosummarization on R6 with its loopback. I wasn't able to get this but i compared this config to the R5 set up since i figured they should be the same and R5 would be working since not mentioned. 


DHCP, IP SLA & NetFlow Sim # 2:
The DHCP portion was darn near spot on. Just had to fix the default-router then flip on the interface on the R6 and finally point vlan 20 to the right spot

The change is that they wanted R2, which they called SW2 to use IP SLA tcp-connect down to R5 over tcp 80. The SW was partially set up but the big thing, going down to R5 and flipping on ip sla responder so it'll reply back as needed.

There was no Netflow on this one for me 

DMVPN OSPF Sim:
Was pretty spot on. The configs were already basically there. Just had to flip on the entire crypto isakmp and ipsec process for H0 and then apply it to the tunnel. There was a note that the BR1 and 2 needed to establish connection directly to one another. I wasn't able to get this to work and the show dmvpn on the BR1 and 2 only showed the hub but the Routers and Sw were able to ping one another just fine.


Remember: Study and know WHY you are doing what you are doing. Not just rote muscle memory.

Hello,

Please review AR677 as the given correct answer can't be correct because that answer has an incorrect tunnel source in the config.  You can't use a tunnel ip as a tunnel source.  Please correct.

Thank you,

Adil

Labs were 

1) VRF EIGRP with the exact same ip address and problems

2) DMVPN OSPF where request was to configure H0, but IPSEC needed to be configure on the BR s, couldnt make it work

3) NEtflow and DHCP: DHCP was working, how netflow has issues in Sw1 instead of R3. R3 had the input and put commands on the e0/0/ interface. Coudlnt make it work


Any help or advise wil be helpful

I want How2Pass to check the CoPP Configuration Sim built into the website as I don't think the "check result" is working properly.  I completed the lab while following the solution yet the "check solution" keeps telling me that I have completed Task 2 incorrectly.

Please check and advise.

Thanks,

Adil

Please look at question QID: AR188.  It mentions a log error message as part of the explanation of the correct answer which isn't in the exhibit.  Also the "correct answer" given fit with the exhibit at all.

Took it today. Failed. VPN section hit me the hardest it seems. 25% all others i was over 70% 

I got a sims similar to "VRF & EIGRP Sim", "DHCP, IP SLA & NetFlow Sim # 2", and a partially configured IPSEC similar to the ones in "IPSec Config Sim" 

the questions were pretty much spot on. I know where i failed. The IPSEC sim asked to disabled EIGRP split horizon where i blanked and also the IP SLA sim i forgot to turn on the icmp-jitter. 

There was also a drag and drop not on this list. Setting up key and encryption drag and drops between two routers.

Are the sims down? Getting "HTTP 500 Internal Server Error" when trying to launch. Verified and tried from 2 computers and phone both on and off my network.

Looking this over:

the R2 L2 and L1 interfaces reside on 192.168.3.2 and 2.2/24

Down the line in the BGP configuration though the commands 
R4(config)#ip prefix-list AS65001-in seq 20 permit 192.168.3.0/24
R4(config)#ip prefix-list AS65001-in seq 30 permit 192.168.2.0/23

and

R5(config)#ip prefix-list AS65001-in seq 20 permit 192.168.2.0/24
R5(config)#ip prefix-list AS65001-in seq 30 permit 192.168.2.0/23 

are suggested. 

Issue that I see is there are no /23 or subnet masks of 255.255.253.0 used 

This will give bad config when implemented. Its doable but will give the wrong information in the show commands.

Please correct me if I am wrong.

Wondering, 

While I am grateful for the sims now having an interactive version so we can practice. 

Can we get more than 15min? I know in real world testing we should do these fast but to get them down we need to slow down and get the practice. Something like 20 or 30min max would be nice.