Ok these two drag and drop subnet questions both puzzle me for many reasons

1/ the questions ask for you to use subnet zero and to conserve host addresses for future use but both questions miss 4 host addresses when
allocating addresses to the serial interfaces n418 issues 192.168.91.197 to the serial link but the next usable host address is 192.168.91.193 so there is 4 missing hosts here and same thing occurs on question n419 where hosts 80-84 are not used

2/ when allocating hosts you should always issue your highest number of hosts to lowest so why does n419 allocate the 78 hosts their subnet last?

3/ going by the same principle of highest to lowest why does the serial link in n418 appear in the middle of the allocation?

4/ why is subnet zero not used in n418 if it is telling you it is in use?

this questions threw me off as they make no sense whatsoever and come with no explanation of how the answer was arrived at


please explain  ???

I've been rolling with how2pass since my first test!  Excellent practice exams and simulators.  Thx How2Pass!

I thought an access list was applied to a router interface as outbound if it is exiting the LAN segment and inbound if it is arriving into the LAN segment from a different segment. So I'm confused as to why the correct answer is shown as

ip access-group 101 in

Should this not be out, since the frame from host 1 will be exiting the FA0/0 interface, heading outbound to the server? I'm so confused.

I had three Labs and one Simlet:

Labs -
OSPF Stub
ISIS/EIGRP Redistribution
IPV6 Virtual Links ???????????? Got it right and I'm not sure how?

Simlet -
EIGRP Topology Output

This is the first time that I have ever taken a certification test and by the end of it I thought that I had failed.  I got crushed with IPV6 and Multicast questions.  I had problems with the Labs.  Once I got into the labs, I couldn't minimize the the telnet session to get into the other router.  I wasted 15 minutes trying to figure out what to do.  Luckily, I was able to telnet from router to router to finish my configuration.  Make sure that you verify your lab configuration because one of my commands didn't show up on the config (what a disaster).  I got a lot of questions that were not on How2Pass and AT.  How2Pass and the other materials helped me get through the exam.

Materials I used:

Training Course and Courseware
CBT Nuggets
How2Pass
AT
Exact Exam Study Guide
Boson Labs
And of Course Real World Experience       

There's a problem with this drag-n-drop question. The IP of the remote server "128.77.88.166" needs to be placed at two places but when you drag it the second time, the IP address changes to 128.77.88.156, which in result, marks the question wrong. Please fix this problem, Thanks!

I'd love to get a hold of the stencils used to prepare the exam questions. Any leads?
Thanks,
Chris

I am finally CCNP Certified ;D ;D ;D  My last exam was ISCW and I scored a total of 1000! I couldn't have done it without the help of How2pass. You have excellent material and many of the things that i didn't grasp while reading Cisco Press books, I got through all your links and explanations to the questions.
Great work guys !  Thanx for all your help ! I will surely recommend you to all my fellow co-workers!

Thanx 

This question states: Under what 2 circumstances would a switch flood a frame? (Select two)

One of the answers for this question is "The MAC address table is full."  However, it doesn't seem like this answer would always be correct.
If the destination address was in the table, then wouldn't the switch forward the frame even if the table was full?

Question 1 ,which was a LAB, immediately locked up and I couldn't type any commands into the routers.

Test supervisor came in and along with his phone tech support, worked for 30 minutes on getting things working.

Finally, and by accident, he clicked the NEXT button, so on to question 2 without doing the first LAB.  Supervisor guy had no clue really what to do next, so they adjusted 22 minutes back on my test, and told me to go ahead and finish it. I don't think he understood how much the Question 1 Lab would count. I'm sitting there thinking $#@&!!!  ???, all that studying for this?

I ended up passing with an 833 without touching the first lab.  Guess they would have given me a voucher if I had failed.  Who knows.. who cares!    I'm not taking it again to see if I can score higher.

Study H2P, make sure you are scoring 95-100% on everything!  I know I answered 3 questions wrong in retrospect, so I should have scored higher.  Anyway, my CCNP is DONE! 

BSCI 833
BCSM 937
ONT 996
ISCW 964

Hello every one.... I have to appear in CCNA 640-802 exam next week I studied from P4s v3.22 (402 Q&A), one of my friend passed ccna 640-802 exam 895/1000 on 20 February 09, he told me that 4 or 5 questions and one simulation of drag and drop were out of form P4s v3.22 (402 Q&A), but today when I visit the Pass4sure.com there is no new update available about P4s v3.23 or P4s v3.24. The latest dumps is P4s v3.22 (402 Q&A) on pass4sure.com. It confused me when I read some post on other forums blog that there is new version available on pass4sure, so please any body help me if some one have latest version P4s v3.23 plz share it with me my email is gmabbasieng@yahoo.com or post a link for download so as i can get it.

Thanking you

GM Abbasi