I need help on 640-802 version 4.25 on question #136 compare to new version  7.25 on question # 273
can anyone tell me what is the right answer in the real exam?

On question 136 on the 4.25 version and question # 273 on the 7.25 version are asking the same question and same digram but each version have different answer ,,can anyone help me the right answer..if you have actuatest.com or copy of both version you and just look at the question # mention and let me.

and
I also have question about the 640-802 exam questions for question # 604 and 611 on the version 7.25, why they both are asking the same question but each one have different answer?

Question say:
When you are troubleshooting an acl isuue on a router, which command can help you to verify
which interfaces are affected by the acl? waht is the real answer for this question: > on question #604 say ans is D but question # 611 say answer is B. so can anyone tell me which one is the right answer?

A. show access-lists
B. show interface
C. show ip interface
D. show ip access-lists
E. list ip interface

Thank..please hope anyone can help.

Pau

Passed 642-902 today! Scored 883 out of 1000, still had 30 minutes remaining when I finished the test.  Test is exactly like H2P, memorize multiple choice and drag and drops. 

Here's the Sims I had:

Lab #3 OSPF Configuration
Lab #4 IPv6 OSPF Virtual-Link
Lab #6 PBR
Lab #7 EIGRP-OSPF Redistribution

Thanks how2pass!!  Good luck to everyone!

Thanks how2pass.  I passed my CCNA and 642-902 (today-981)  with your help.

Just finished the ICND1 test. 40 minutes to complete. Took my time to verify the answers before submitting.

One thing I did to help speed things up was to write out all of the multiples of 4, 8, 16 and 32. This makes finding ranges a breeze.

Are the testlets, simlets, simulations etc scored all or nothing or do you get partial credit for the correct answers you give?

I'm having some difficulty understanding how a tunnel interface is used. I get the basic config, but what traffic is sent across the tunnel?

Thanks

Tom

I won't post all of my details but I did pass. The first 6 questions I had not seen before but they were easy enough to rule out at least to 2 possible right answers. Make sure to go through the labs on here!!! I had Lab 4, Lab 6 and Lab 7. Be careful they have 2 different types of labs, some are a full lab which doesn't allow you to copy run start, and they just want you to push next when you are done, and then there were smaller mini-lab environments where you could, I am not sure if not doing a copy run start counts against you but I would suspect that it would be in your best interest to go ahead and try anyhow.

I just went through each section here on How2pass and did all the questions until I could do all of them with at least 80%... I did fine in the test. Thanks How2pass, I am even taking a college class for this but you guys have an invaluable tool here, and I tell everyone I take classes with to check it out when they are ready to certify.

Most of the questions from how2pass, perhaps 4 or 5 new questions that are not from how2pass.
Labs 3 5 6 7

Score  860

100 eigrp
89  ospf
100  ebgp
100  ipv8
25  redistribution
33  layer 3 path control

Overall if you memorized all the questions from how2pass and studied labs 1-5 WHICH ARE EASY you can sacrifice labs 6 and 7 on the exam and still get nice score.  Since they just started this exam, they did not have lot of time to add new questions to it, so good time to take it would be right now 09-07-2011 before they add new questions.  The key to passing this exam is memorizing all the how2pass answers and memorizing labs 1-5.  Write out labs with a pen or open a notepad and type in commands from memory.

Are there plans in the works for adding interactive versions of hands-on labs 4-7?

I use How2Pass for both of my CCNA tests and now just passed the ROUT exam.  I scored an 833 not too bad enough to pass.  Moving on to SWITCH.