| Welcome, Guest |
You have to register before you can post on our site.
|
| Latest Threads |
Sim Time
Forum: CCNP ENARSI 300-410 Forum
Last Post: ratedr
07-15-2026, 05:43 PM
» Replies: 6
» Views: 1,801
|
AR085 Seem Wrong
Forum: CCNP ENARSI 300-410 Forum
Last Post: ratedr
07-13-2026, 12:11 AM
» Replies: 0
» Views: 110
|
Passed! My Notes
Forum: CCNP ENARSI 300-410 Forum
Last Post: adilnasser3
07-05-2026, 10:56 PM
» Replies: 3
» Views: 508
|
QID: AR677 Answer is wron...
Forum: CCNP ENARSI 300-410 Forum
Last Post: help_desk
07-03-2026, 10:20 AM
» Replies: 3
» Views: 501
|
Failed Exam 6/17
Forum: CCNP ENARSI 300-410 Forum
Last Post: help_desk
06-20-2026, 07:12 AM
» Replies: 2
» Views: 680
|
Just Passed! Corrected La...
Forum: CCNP ENARSI 300-410 Forum
Last Post: forumsupport
06-15-2026, 03:00 AM
» Replies: 2
» Views: 11,823
|
CoPP Configuraton Simulat...
Forum: CCNP ENARSI 300-410 Forum
Last Post: help_desk
06-10-2026, 07:05 AM
» Replies: 1
» Views: 538
|
QID: AR188 - Question/Ans...
Forum: CCNP ENARSI 300-410 Forum
Last Post: help_desk
06-04-2026, 07:05 AM
» Replies: 1
» Views: 653
|
Failed
Forum: CCNP ENARSI 300-410 Forum
Last Post: help_desk
05-30-2026, 07:16 AM
» Replies: 2
» Views: 996
|
SIM down?
Forum: General Discussion
Last Post: elpotatoexperto
05-29-2026, 11:29 AM
» Replies: 2
» Views: 966
|
|
|
| eBGP Neighbor Sim |
|
Posted by: Holyak - 05-20-2025, 11:18 AM - Forum: CCNP ENCOR 350-401 Forum
- No Replies
|
 |
Task 1 requires the ebgp to be configured using L0 on R3 as the router ID. Hence, the command " bgp router-id 3.3.3.3 " is missing in the solution.
Can we have a review?
|
|
|
| QID:EC956 |
|
Posted by: Holyak - 05-17-2025, 07:08 AM - Forum: CCNP ENCOR 350-401 Forum
- Replies (2)
|
|
ip access-group 101 for the interface Gi0/0 with the IP; 10.0.0.1/24 should be applied on the IN direction as opposed to the OUT direction in the answer. Can we please have a review?
|
|
|
|
| CCNP 1.1 |
|
Posted by: elpotatoexperto - 05-06-2025, 10:03 PM - Forum: General Discussion
- Replies (1)
|
|
Stepped away for a short period to lick my wounds.
Now I see there is a 1.1 version of the ENCOR. Should I review that one only or both the 1.1 and original sets?
|
|
|
|
| AN955 |
|
Posted by: jcurless - 05-05-2025, 04:18 PM - Forum: Answer this question
- Replies (1)
|
|
Q: refer to the exhibit. which configuration enables SW2 to establish an LACP EtherChannel?
In the exhibit it shows two Switches listed as SW2. (with below config)
SW1#show run
building configuration
interface GigabitEthernet0/1
channel-group 2 mode passive
!
interface GigabitEthernet0/2
channel-group 2 mode passive
The answer it says is correct has different Channel-Group ID's...
SW2(config)#interface gigabitEthernet0/1
SW2(config)#channel-group 1 mode active
SW2(config)#interface gigabitEthernet0/2
SW2(config)#channel-group 1 mode active
The only answers that list channel-group 2 are mode desirable and auto.
|
|
|
|
| AN668 |
|
Posted by: smokinu - 04-10-2025, 12:46 AM - Forum: Answer this question
- Replies (1)
|
 |
Question:
The IPv6 address for the LAN segment for the LAN Segment on router R2 must be configured using the EUI-64 bit format. Which address must be used?
Answer:
ipv6 address 2001: DB8: D8D2:1009:ABFF:FECC:1
Answer should be:
ipv6 address 2001: DB8: D8D2:1009:ABFF:FEDD:2
* I think this should be the correct answer due to only the 7th bit is converted using EUI64 method.
Am i correct? The Exhibit shows that the mac address for the LAN segment is "12-a0-ab-dd-00-02.
|
|
|
|
|
