Recently lot of my students have complained that they only got 4 questions out of ICND2 exam material available on this site , the labs are fine (VTP and Frame Relay Sim popular). ICND1 exam did have good feedback . Any Idea if Cisco has changed the exam or this site is not updated .

Just passed icnd 2 this morning. Originally i failed icnd 2 by 5 points and my teacher showed me how2pass and the rest is history. After i had failed i waited the 1 week before taking it again and passed thanks to how2pass. My sources are packet tracer;todd ccna book and how2pass.

With this question, about CDP, the exhibit gives us the Bravo router IP is 10.1.1.2

The answer says we can tell from the output the Alpha router IP is 10.1.1.1.  How? It could be a few different ones depending how it is subnetted

Hello everyone,

I just passed today 642-902 with score 930.
Again, I recommend Cisco Press and CBT nuggets to understand the concepts and foundations, and afterwards H2P.

I had 4 simulations, 53 questions in total. In my case 3 minutes left, so time is running fast.
If you not understand Hands-on labs and you are not able to solve those in less than 10 minutes, simply you are not ready for the exam.

Good luck...

This answer seems to me to be wrong.  What do others think?

There are 3 routers connected via serial links. The routers have 27 hosts, 17 hosts and the one we are looking at has 13 hosts.  The question is which address should the fast ethernet address have.

We are subnetting on 192.168.1.0 with a mask of 255.255.255.224

That's ok so far, but is says we are using RIP1.  How would that work with a subnet of 224.  Surely it would not see the subnetted bits if using RIP1?

The answer I find even more strange.  Options are:

xx.xx.xx.64
xx.xx.xx.192
xx.xx.xx.190
xx.xx.xx.31
xx.xx.xx.127

I went for 64 as 192 seemed less correct.

The answer was 190, because all the others are either broadcasts or subnets.  But if we are looking for a fast ethernet port from a router with a number of hosts, it would be subnet address surely no?

So on this question, it asks what error condition can be immediately ruled out, when troubleshooting a LAN interface operation in full duplex mode. The answer it gives, collisions, is the best answer of those given, however, wouldn't collisions still be a possibility if the LAN segment exceeds the max cable length? Just a couple weeks ago at work, in fact, we had this issue where an end user was connected to their access switch using an Cat5 cable that was probably about 20 - 30 feet over the max length, and they had collision issues.

Hi, just have query regarding answer provided for this question.

Q. What happens when computers on a private network attempt to connect to the internet through a Cisco router running PAT?

Correct answer: The router uses the same IP address but a different TCP source port number for each connection.

I understand PAT is about port translation & assigning different port numbers to connections. But PAT is also another name for NAT which is about translating private addresses to public. Here we have a private network going through a PAT router so I assume it is using private addresses - these private addresses need to be translated to public so should the answer not be the option below:

The router assigns a unique IP address from a pool of legally registered addresses for the duration of the connection.

Thanks

I am trying to setup my home lab.

Its consists of 3 2610s, 2 2950s and 1 3550.

I want to use the 3550 as a layer 2 switch only (at this point).

Im having problems getting it to connect to the 2610.

I see the vlan 1 and fa0/1 (in switchport mode) up. But CDP isnt working.

Can someone point me in the right direction ? Output is given below ...

3550_1#show ip int br
Interface                  IP-Address      OK? Method Status                Protocol
Vlan1                      192.168.10.3    YES manual up                    up
FastEthernet0/1            unassigned      YES unset  up                    up
FastEthernet0/2            unassigned      YES unset  down                  down
FastEthernet0/3            unassigned      YES unset  down                  down
FastEthernet0/4            unassigned      YES unset  down                  down

3550_1#show cdp nei det
3550_1#

I just took my CCNA recently after using this site and passed with a score over 930. I don't want to be specific because I'm paranoid.

Questions: It's hard to gauge how many related directly to the exam here, but I'd say maybe 50% to 75%, or possibly more if I just forgot & didn't recognize. There are >900 test questions to review and it takes a long time to review them all. I'm pretty sure there were new ones. I know they changed the ACL SIM (question QID:S17). Essentially they wanted me to allow x.x.x.2 instead of x.x.x.3. The name of the server they wanted to restrict was named Financial Accounting or something like that. Also, they wanted only this 1 host access via web browser, but wanted to block all other types of access from that computer & all other host computers + core. I wrote my access list like:

• access-list 100 permit tcp host [x.x.x.3 PC] host [x.x.x.17 server] eq 80
  
• access-list 100 deny ip any host [x.x.x.17 server]
  
• access-list 100 permit ip any any

I'm a little confused by the question:
An administrator is in the process of changing the configuration of a router.  What command will allow the administrator to check the changes that have been made prior to saving the new configuration?

Correct Answer: Router#show running-config

There's a very good chance that I'm misinterpreting this question, but shouldn't the admin be checking the startup-configuration if they want to compare before saving?  Unless the running-config hasn't been altered, wouldn't a sh run show their current configuration rather than prior?

I think I may need to lay down.