This site is swesome.  If I would have studied IPv6 more thoroughly I probably would have aced the exam.  Good luck to all who are preparing to sit for this exam.  You'll pass. 

Took and passed ICND2 with a score of 902 on my 1st attempt yesterday.

Prep time was 3 months (right after passing ICND1), and included TestOut LabSim CCNA course, CCNA ICND Exam Cert Guide by Wendell Odom, CBT Nuggets, and of course how2pass ICND2 practice tests. The two primary study materials were TestOut Labsim and how2pass.

lots of questions on the exam covered here... I didn't complete the access-list Sim or the EIGRP sim, but completed most of the EIGRP. I got a score of 920! Good luck you can do it!

-----------------------------------------------------------------------
Don't write how many questions were same or not.
Forum Admin

I passed the route exam today with a score of 965.  I went through the networking academy, and after completion only used how2pass to prepare for the exam...  Just understand the reason behind the answers and you will be fine.

-----------------------------------------------------------------------
Don't write how many questions were same or not.
Forum Admin

ref: QID:S27

I worked on this question for the last two & got the respected outcome fine. But today, it acted a little strange??

The folowing details will highlight where I'm coming from;

SAVED IN CONFIG
----------------------------------------------------
router rip
version 2
network 192.0.1.0
network 209.165.201.0
!
ip classless



YET
------------------------
Bravo#sh ip protocol
Routing Protocol is "rip"
    Sending updates every 30 seconds, next due in 12 seconds
    Invalid after 180 seconds, hold down 180, flushed after 240
    Outgoing update filter list for all interfaces is
    Incoming update filter list for all interfaces is
    Redistributing: rip
    Default version control: send version 1, receive any version
        Interface            Send    Recv    Key-chain
        Serial0/0                2        1 2
        FastEthernet0/0        2        1 2
    Routing for Networks:
      192.0.1.128
      209.165.201.0
    Routing Information Sources:
        Gateway        Distance        Last Update
        192.0.2.129    120                00:00:21
    Distance: (default is 120)


As you can see I'ved saved in the config, router RIP version 2, but 'ip protocol' claims I was running version 1....Freaky or what.

Was there a problem on your servers today or something.

Even more freakishly it marked my answer right, which i was chuffed with.


Just though you Admin bods should know...

Keep up the good work...

The correct answer shows that  it is a  /22 ....  Just wandering if it should be /24 ?  Help  thanks

To All,

My ISP is Btinternet and I have recently purchased a Cisco 837 Router and I have performed the below configuration which I believe is incorrect?

I am attempting to use this router for my main ADSL to access my network with the above ISP.

Interface e0
Description Ethernet
ip address 192.168.1.3 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
exit
interface ATM0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
no atm ilmi-keepalive
dsl operating-mode auto
pvc 0/38
encapsulation aal5mux ppp dialer
dialer pool-member 1
exit
interface Dialer0
ip nat outside
ip address negotiated
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication chap callin
ppp chap hostname  myuser@adsl.user.name.com
ppp chap password 0 adslpassword

Can you please help with necessary corrections

Much Appreciated!

reb999000.

The question states:
"What does a router do if it has no EIGRP feasible successor route to a destination network and the successor route to that destination network is in active state."

The answer should be:
It routes all traffic that is addressed to the destination network to the interface indicated in the routing table.

Explanation:
Since the successor route is in active state, it does not need a feasible successor route. EIGRP only cares that a route is working in this case. Now if the successor route should fail, then it would send a multicast query packet to adjacent neighbors requesting available routing paths to the destination network.

I finished taking my CCNA 640-802 exam today and I passed with 907/1000. I still had 40 mins left to go. I encourage everyone to make sure you score 90% or above on every section of How2Pass. Most of the questions were similar on the exam. You still have to have an understanding of the concept and just not remember answers. Without How2Pass, I know i would've failed. The hands on experience of the labs is a big plus. My exam included EIGRP, VTP, and ACL. I read the CCNA books for month from top to bottom of the Wendell Odom suggested by How2pass and I studied How2pass almost daily for 1-2hrs making sure I was mastering the material. On today, I ran over questions for 3hrs until it was time for test time. I'm glad I did because some of the similar questions appeared on the exam and were still fresh in my mind.

This is my 2nd go around using How2pass and it is worth every penny. It is less expensive than other practice test sites and the hands on experience is advantageous. I first used How2pass 3years ago and I passed the exam.

thanks How2pass!!!!!!

host IP 10.0.0.249
subnet mask 255.255.255.0
Question is what should the default gateway be

With this mask, the range is 10.0.0.0 to 255
.0 should be the gateway and 255 the broadcast

Why then does the explanation say 10.0.0.0 cannot be used as a host (the question was regarding the gateway, not the host) and it says the gateway would be 254.  Why would you have a default gateway as 254 on this mask - that would be madness and a waste of hosts!!!